Antique Sewing Machine Drawer Upcycle

For this Antique Sewing Machine Drawer Upcycle, we used the drawers from an old Singer to make a rolling storage solution for our craft room!

A couple of winters ago, I got a message from an old friend and coworker. Her mother had just passed, and she was faced with the difficult task of cleaning out her mother’s home in southwestern Connecticut. Not wanting all of her mother’s possessions (and her memories) to be sold to strangers, Paulina asked if Handan and I would be interested in taking some of the pieces to use and work on for the blog.

We agreed!

Some of the furniture we put to use as-is, other pieces are marked for future projects, and one was just perfect for our craft room makeover.

This beautiful antique Singer sewing machine served Paulina’s mom for decades.

It was well-loved and well-used. It would have needed some work to make it functional again as-is, but Handan knew that we could do something awesome with those antique sewing machine drawers.

She kept those drawers in mind as the months ticked by. They had to fill a need. The project had to make sense and fulfill a purpose.

And my babes just found their purpose!

Our craft room makeover is all about storage solutions, big and small.

I just showed you our big solution with the West Elm inspired DIY storage towers, and these little drawers are a perfect small-item storage solution.

Let’s have a look at how we did it.

Antique Sewing Machine Drawer Upcycle

So I’ve told you many times how bananas Handan is about ornate picture frames. What I haven’t told is that she is equally bonkers about spindles.

And I mean loony, ladies!

Yep, we’ve got spindles coming out the wazoo, and that’s no place for a spindle!

o_0

Anyway, for 6 years, my babes has been chopping spindles off everything from baby cribs to broken headboards to beaten-up hutches. Of course, when I say, “my babes has been chopping,” I mean I’ve been chopping… under direct orders from ze Commandant.

And what has my beloved babes done with the hundreds of spindles squirreled in every nook and cranny of our basement?

Well, there was this gilded bowl centerpiece, for one.

And then there was this tiered stand she made.

But other than that?

Yep, a whole lotta nuthin’ on the spindle front!

6 years of intensive spindle farming and only two measly projects to show for it!

Who here wants my babes and me to make more spindle projects? Let us know in the comments!

No Spindle Left Behind!

That’s my new slogan and the platform I’m running on as a candidate for Blogger-in-Chief!

To prove my commitment to our new Spindle Initiative, I shall incorporate them into this antique sewing machine drawer upcycle!

Here’s what we started with.

Now, those spindles were too long for what we needed, so I cut them to size.

And guess what?

This created 8 spindles where once there were 4.

So even after this project, we still have the same number of spindles hiding in our basement!

GAH!

Anyway, the idea was to make a rolling storage cart for the antique sewing machine drawers using spindles and some 1/2 inch plywood.

But first, we had to attend to the drawers. Time and use had taken their toll (just like on me.)

I removed the frame around the top of each drawer cabinet.

Next, I removed the drawers. You may have noticed in the earlier photo that one of the drawers was missing a chunk. We figured I’d have to sculpt a replacement from scrap wood and glue it in place.

But as I prepared to repair one of the broken cabinets…

Behold!

The missing piece!

Ooooh….

Fits like a glove!

That piece had fallen off before, as evidenced by the dried glue on it and on the drawer.

We scraped off the old glue as best we could, and then I glued it back together with super glue. Wood glue wouldn’t work well, since the wood pores were already sealed off from Paulina’s mom’s earlier attempts to fix this pesky little drawer.

Insta-Set accelerator is the best! They’re not at all kidding about the instant part!

Good as new! Paulina’s mom would be proud!

One of the drawer cabinets was coming apart at the seams.

So we used a little glue…

And…can you guess??

Yep!

Brad nails!

Good guess, smarty pants!

With the repair work done, we started in on the build.

We have very specific plans for this little antique sewing machine drawer cart, not only for what it will store but also for where it will live in our craft room.

Though it can be moved anywhere since it’ll be on wheels, we designed it primarily to fit in two places:

1. Underneath our DIY Craft Table
2. Against a wall that is 16 inches wide

With that in mind, I cut 3 pieces of 1/2 inch plywood to 16 inches wide by 14 3/4 inches deep. This included a 1/2 inch overhang all around.

I marked a line around two pieces of plywood (the top and the middle piece), 1/2 inch in from the edge, and then I sanded the sharp edges from all 3 pieces (no more rough edges or tear-out when cutting plywood thanks to this little miracle!)

Then I applied some wood glue all around the bottoms of the drawer cabinets.

After smearing the glue around with my finger, I positioned the two cabinets on the lines I had drawn around the plywood.

I put some clamps to hold everything together, and then I carefully flipped it over. Note that it is actually upside-down in the picture below.

I shot a bunch of brad nails to secure the plywood to the cabinets, and then we flipped it back over again.

Someone’s sure satisfied with his little project!

Next up – the top!

Just like I did with the middle piece, I smeared glue around the tops of the cabinets.

And then I inverted everything so I could position it on the plywood.

I clamped it up…

And flipped it over. In case you’re getting lost, it is now right-side up.

The next trick was to attach the spindles and bottom piece of plywood.

And it was tricky problem as we didn’t have double-sided screws! (But we figured it out.)

First, I drilled pilot holes through the bottom piece according to where we wanted the center of the spindles to be. The two metal blocks I’m using are makeshift guides to help me drill straight through and not at an angle.

I would need to pre-drill both ends of each spindle, as I’d be screwing into them from either side.

Before drilling, I marked the centers of each end of each spindle.

I pre-drilled the bottom ends of each spindle.

Then I put a screw up through the plywood from the bottom. I used a small dab of construction adhesive on the bottom of the spindle to keep it locked in place.

In order to attach the spindles to the upper part of the cabinet, we decided the best solution was first to screw the spindles to a piece of 1/4 inch plywood that was slightly smaller than the 1/2 inch pieces and then glue and brad nail the 1/4 inch piece to the 1/2 inch. Sounds more complicated than it is.

In order to mark where the spindle centers would meet the 1/4 inch plywood (so I’d know where to drill), I cut small pieces of brad nails and gently tapped them into the marked centers on the tops of the spindles.

I then laid the piece of 1/4 inch plywood on top of the spindles. When I had it centered, I tapped the 4 corners so the brad nails punctured the plywood.

This showed me where I had to drill.

I pre-drilled the 4 brad nail holes with a countersink drill bit.

After removing the small brad nail pieces, I pre-drilled the spindles.

I then put screws down through the holes I made in the plywood and placed it on the spindles.

Once I had all the screws in the 4 holes, I tightened everything up.

Okay, that completed the base. The next step was to join the base to the cabinet.

I flipped the cabinet over and dry-fit the base. Since the 1/4 inch plywood is smaller than the 1/2 inch, I marked around it with pencil, so I’d know where to put it after spreading some glue.

Then I lowered the base in position according to my pencil lines.

I shot a bunch of brad nails all around the edges, corners and randomly around the middle to keep the base firmly in place.

Flipping it back over, it looked like this.

The only things left were to add the casters and stain the plywood, and those two activities were done without my babes to take my picture!

I color-matched as best I could by mixing Varathane Kona and Varathane Light Walnut (for the reddish tones). I cleaned the spindles, cabinet and drawers with Krud Kutter, then also wiped stain over them to further match the color.

So, what do you think? Did I nail the color?

Do you like our new small storage solution for the craft room? It’s a perfect organizer for the small tools we use all the time.

Here is one of its homes. You can see now why it had to be 16 inches wide.

And if it’s not needed for a while, and we’re not working at the Cricut Command Center, it fits perfectly underneath!

Everything in this room has been carefully thought out and designed with a purpose, since this small room needs to fill three roles: a video & photography studio, a home office and a craft room.

Now, you know who’s responsible for that, don’t you?

Lord knows I couldn’t plan my way out of an empty room with no walls, so you know it wasn’t me! 🙂

Well, folks, little by little we’re getting closer to our craft room makeover reveal!

Stay tuned for more!

If you’re following along with the craft room makeover, here’s how we stand:

Craft Room Makeover Checklist

• Craft room ideas and laying out the game plan
• Paint the walls, ceiling and trim
• Paint the French door
• Carpet removal
• Install laminate flooring
• Buy curtains and install curtain rods
• DIY craft table for Cricut
• DIY / buy a computer desk
• DIY Closet makeover
• DIY Industrial Bookcase (West Elm Inspired)
• Antique sewing machine drawers upcycled to a storage cart
• Upcycled craft room storage
• Craft room makeover reveal

Click here to see more craft room makeover posts as we continue to cross items off our checklist!

We love it when you share our posts on Facebook and Pinterest!